Home >> Lifestyle: Cleaning Center: Floor Cleaning and Care

 

Floor Cleaning And Care - pg2

 

Candy Stains on Hard Surface Floors

Rub with a cloth dampened in detergent and warm water. For abrasive action, use steel wool instead of a cloth except on "no wax", or hard-surface floors. On them use powdered detergent and a plastic scrubbing pad dampened with warm water.

Cautions: When working with any chemicals, carefully read and follow the label directions for using that chemical, especially any cautions on safe use! With solvents, be very careful to have ventilation, and no flame or spark in area!

The first time you use any procedure on any floor, test it first on an out-of-the-way part of the floor to be sure it does not damage the flooring or finish.

Notes: If steel wool is suggested, use fine grade, 000 grade.

Scouring powder will help remove many stains, but can also permanently scratch the floor. If you decide to use it, use only a mild type, and be very careful about rubbing too much.

Concentrated liquid commercial household cleaners, rubbed onto a stubborn spot, may remove it as well as scouring powders without the danger of scratching. Rinse off well. Do not use on wood floors.

Do not use water solutions, or cleaners which have to be rinsed off with water, on wood floors. Use a solvent or solvent-based cleaning wax.

After removing a stain, rinse the area thoroughly, dry completely, and, if floor finish has been removed in that area, recoat with appropriate finish or wax.

Concrete, Cement - Grease Stains

In a garage, it is advisable to place a shallow metal pan under the car to catch dripping oil. Spreading the area under the car with sand or sawdust will help absorb dripping oil. Periodically saturated sand or sawdust should be scraped away and fresh, clean material put in place. This will prevent tracking oil to other areas of cement or into the house.

If oil or grease is spilled on porch or patio cement, apply an absorbent powder such as fuller's earth, cornmeal, or sawdust to absorb as much oil as possible immediately. Leave it on stain for a few hours and sweep up.

To remove the grease stain:

1. Using a stiff long handled brush, scrub stain with concentrated detergent suds. Rinse well with hose. Dry and repeat if necessary.

2. Sprinkle "dishwasher" detergent (dry) on wet concrete. Let it stand a few minutes; pour boiling water on area. Scrub and rinse. Use rubber gloves on hands.

3. Commercial Product: One brand is Garage and Driveway Cleaner by Red Devil Co. available in paint or/and hardware stores. It can also be used on blacktop surfaces. Other similar brands may be available in your area.

4. On wet oily surface of concrete, sprinkle with trisodium phosphate. Allow to stand 15 to 30 minutes, then scrub with stiff brush and hot water. Rinse with clean water. Do not use on asphalt.

OR: Dissolve a cup trisodium of phosphate in 1 gallon of hot water. Pour over stained cement surface generously and allow to soak 15 to 20 minutes. Scrub vigorously with stiff brush or broom. Rinse off with hose. Repeat if necessary. Do not use on asphalt.

5. Scrub the concrete with a grease solvent to remove as much as possible of the grease stain. Have good ventilation and avoid spark or flame as solvents are flammable. Benzine, often recommended, can ignite, just from a spark from friction or rubbing.

6. Mix 1 part sodium citrate to 6 parts water and 6 parts glycerine and add enough whiting or fuller's earth to make a thick paste. Spread paste on oil or grease stain. Let stand 1 week. Add new paste when it dries. Flush with water after brushing dry paste away. Repeat if necessary.

next page

The Author:

Anne Field, Extension Specialist, with credit to MSU Extension

• print this page